Ashland County, Ohio
Electrical Code Checklist

Make sure your electrical work meets local building codes before the inspector comes out. Covers Ashland County requirements based on Local building code.

Start checking now

Free to try. Works on your phone.

What's in the checklist

Service Equipment

✅Main service disconnect must be located at a readily accessible point nearest the point of entrance of the service conductorsNEC 230.70(A)(1)
✅Service panel working clearance must be at least 36 inches deep in front of the panel (min 36 inch)NEC 110.26(A)(1)
✅Service panel must have a clear width of at least 30 inches in front of the equipment (min 30 inch)NEC 110.26(A)(2)
✅Main service breaker rating must match the calculated load for the dwelling unitNEC 230.79

Branch Circuits

✅Kitchen small appliance branch circuits must use 12 AWG wire (20A rated)NEC 210.11(C)(1)
✅General-purpose 20A branch circuits must use wire no smaller than 12 AWG copperNEC 210.19(A)(4)
✅Maximum of 10 receptacles per 15A branch circuit or 13 per 20A circuit (max 13 count)NEC 220.14(I)
✅Dedicated 20A circuit required for bathroom receptaclesNEC 210.11(C)(3)

Receptacles

✅Wall receptacles must be placed so no point along the wall is more than 6 feet from an outlet (max 6 feet)NEC 210.52(A)(1)
✅Kitchen countertop receptacles must be placed so no point along the counter is more than 24 inches from an outlet (max 24 inch)NEC 210.52(C)(1)
✅At least one receptacle must be installed within 3 feet of each bathroom basin (max 3 feet)NEC 210.52(D)
✅At least one receptacle required at the front and back of the dwelling, accessible at grade levelNEC 210.52(E)

GFCI/AFCI Protection

✅GFCI protection required for all receptacles in bathrooms, garages, and outdoor locationsNEC 210.8(A)(2)(3)(10)
✅AFCI protection required for all branch circuits supplying bedrooms, living rooms, and similar habitable spacesNEC 210.12(A)
✅GFCI protection required for kitchen countertop receptacles, dishwasher, and similar wet-area appliancesNEC 210.8(A)(6)(7)
✅All 15A and 20A receptacles in dwelling units must be listed tamper-resistantNEC 406.12

Bonding & Grounding

✅Grounding electrode system must include a minimum 5/8-inch by 8-foot ground rod (min 8 feet)NEC 250.52(A)(5)
✅Equipment grounding conductor for 20A circuits must be at least 12 AWG copperNEC 250.122
✅Metallic water piping system must be bonded to the grounding electrode systemNEC 250.104(A)
✅Grounding electrode conductor must be continuous from the service equipment to the grounding electrodeNEC 250.64(C)

Based on Local building code. This checklist reflects state-level code requirements — always consult the local Authority Having Jurisdiction (AHJ) for any county-specific amendments before construction.

Frequently asked questions

Does a electrical project in Ashland County need a permit?

Most electrical work in Ashland County, Ohio requires a building permit before construction. CodeCheckHQ helps you verify your work meets Local building code requirements before the inspector arrives.

What codes apply to Ashland County electrical work?

Ashland County follows Local building code with local amendments. CodeCheckHQ checklists are derived from these codes and reflect state-level modifications.

How long does a electrical inspection take in Ashland County?

A typical electrical inspection in Ashland County takes 30-60 minutes. Pre-walk the CodeCheckHQ checklist to identify and fix issues before scheduling.

Can I use CodeCheckHQ for a Ashland County electrical self-inspection?

Yes. CodeCheckHQ is a pre-inspection self-audit tool — not a replacement for the official AHJ inspection. Use it to catch issues early; official approval must come from a licensed inspector.

Don't guess. Check it now.

Ashland County building code requirements in plain English. Mark each item Pass, Fail, or N/A. Get a PDF report.

Start free check

Ashland County, OhioElectrical Code Checklist

What's in the checklist

Service Equipment

Branch Circuits

Receptacles

GFCI/AFCI Protection

Bonding & Grounding

Frequently asked questions

Does a electrical project in Ashland County need a permit?

What codes apply to Ashland County electrical work?

How long does a electrical inspection take in Ashland County?

Can I use CodeCheckHQ for a Ashland County electrical self-inspection?

Don't guess. Check it now.

Ashland County, OhioElectrical Code Checklist

What's in the checklist

Service Equipment

Branch Circuits

Receptacles

GFCI/AFCI Protection

Bonding & Grounding

Frequently asked questions

Does a electrical project in Ashland County need a permit?

What codes apply to Ashland County electrical work?

How long does a electrical inspection take in Ashland County?

Can I use CodeCheckHQ for a Ashland County electrical self-inspection?

Don't guess. Check it now.

Ashland County, Ohio
Electrical Code Checklist

Ashland County, Ohio
Electrical Code Checklist